AUTOMATIC PRE-WASH ZONE

 

AUTOMATIC PRE-WASH ZONE - Pre-spray systems

Foam spray device, aluminum premium arch, LED illumination, including program indication

Eye-catching entrance portal made from powder-coated aluminum with vehicle and height identification system. Front side covered with translucent, labeled plastic plates. Illuminated system: 1 Lamp compartment in lateral beam, 1 lamp compartment in left and right side beam, up to 6 additional illuminated LED-program indications in left side beam.
A program ticker can be purchased optionally.

Alternative arch versions:
a) Without program indication (left side piece also with drive-in pointers)
b) Without foam fan spray jets and foam reactor /as pre-spray arch with flat spray jets)
 

Foam flat spray jets from Christ

For special visual optics on the foam arch. The foam carpet is applied evenly and well targeted. Cost-efficient: Reduced chemical and water consumption.
 

Program ticker

For displaying advertising and promotions. With PC software for free text programming.
 

Pre-spray device, aluminum premium arch, not illuminated

Frontside covered with labelled plastic plate coverings. No lighting system. Alternative arch model: With foam flat spray jets and foam reactor (instead of flat spray jets)
 

Rim spray device free-standing.

Rim cleaner is sprayed onto the rims in order to losen the dirt. The device is light barrier controlled.
 

Chemcial spray device front/rear.

This special device is irreplaceable in express wash tunnel concepts. The spray device consists of two spray pipes  and is delivered with 2 dosing pumps (for various pre-cleaning chemicals). The first spray pipe sprays against the lower front area (insect area) and the second spray pipe against the lower rear area (around exhaust pipe grime).
 

 

High-pressure pre-wash systems

JETSTREAM-EXPRESS

An effective and powerful automatic high-pressure wash is strongly recommended for express wash concepts in order to prepare the vehicle for the subsequent brush wash. JETSTREAM-EXPRESS powerfully sprays the vehicle with its 5 oscillating high-pressure jet devices (Point spray jet). A working pressure of up to 50 bar at approx. 140 ltr/min can be achieved in combination with two piston membrane pumps suited for recycled water (up to 250 μm particle size). The jet devices spray against the vehicle at the start of the program and pivot in towards the vehicle’s end in the rear area for  a thorough rear wash. The side devices work in alternating operation according to vehicle area. Frame material: Duraprotect
 

JETSTREAM SEMI-EXPRESS

Ideal for wash tunnels with semi-express wash concepts. The arch relieves the pre wash personnel and thus reduces the workload. The vehicle is cleaned by 4 oscillating high-pressure jet units (working pressure approx. 50 bar at approx. 70 ltr./min.) These spray parallel to the vehicle and turn towards the rear of the vehicle once reaching the vehicle’s end. Frame material: Duraprotect.
 

JETSTREAM-MATRIX Combination

The JETSTREAM-EXPRESS or the JETSTREAM SEMIEXPRESS can be mounted directly on the high-pressure wheel/sill washer MATRIX. This way, a compact highpressure pre-wash combination is created. We are flexible: Upon request, we can also combine piston membrane pumps with 80 bar and adjust the amount of high-pressure jet devices according to the specific project.
 

 

Pre-wash systems

Middle-pressure spray device, mounted on Evolution Wash Portal

For full-surface rinsing of softened dirt by middlepressure spray jets. The spray pipe can be mounted to various Evolution Wash Portals (in the picture on the frame of the kinematic roof cylinder). Designed for supply by centrifugal pump up to 16 bar at 100 ltr./min.
 

Middle-pressure spray device, DURAPROTECT arch.

High-grade middle-pressure arch in DURAPROTECT frame material. The piping with the spray jets is mounted on the rear of the arch. The arch is designed for supply by a centrifugal pump up to 16 bar at 100 ltr./min. (upon request also combineable with piston membrane pumps).
 

Middle-pressure spray device, aluminum profile arch

Cost-efficient middle-pressure arch designed with powder coated aluminium frame profile. The piping with the spray jets is mounted on the rear side of the arch on mounting consoles. The arch is  designed for supply by a centrifugal pump up to 16 bar at 100 ltr./min.100 l/min.
 

 

High-pressure wheel wash systems

Wheel / sill wash device TIREJET

The TIREJET cleans the sill and wheel areas, with an electrically driven, 360° rotating high-pressure jet  device. It is ideally situated following a brush wheel wash unit in order to rinse off softened rim dirt. Working pressure: up to 50 bar at approx. 70 ltr./min. (supply via piston membrane pump capable of functioning with recycled water).
 

Wheel-/ Sill wash device HD-ROTATION, accompanying

Effective high-pressure cleaning for sill and rim areas. HP-ROTATION is especially designed for installation and application following the wheel brush wash unit. Two oscillating high-pressure devices wash dirt off of each side (0° jets) of the vehicle in an accompanying movement (1.000 mm). A working pressure of up to 80 bar at approx. 70 ltr./min. can be achieved in combination with a piston membrane pump suited for use with recycled water (up to 250μm particle size).

Optional: Pivoting device
Pivoting device for 3 adjusted angles: Slanted against vehicle front corners, then parallel to the vehicle, then slanted against vehicle rear corners.

Wheel / sill wash device HP-MATRIX, accompanying

For high-pressure cleaning of sill and rim areas and especially wheel arches. This aggregate is the ideal complement for wash tunnels with an express wash concept. Large dirt particles are thoroughly removed and the vehicle is ideally prepared for the following wash stations. Two oscillating high-pressure devices wash dirt off of each side (0° jets) of the vehicle in an accompanying movement (1.000 mm).

The vehicle front and rear are washed by a pneumatic pivoting movement. A working pressure of approx. 50 bar at approx. 69 ltr./min can be achieved incombination with two recycled water suitable piston membrane pumps (up to 250 μm particle size).
 

 

Automatic wheel wash systems

Wheel / sill wash device, longitudinal

For intensive cleaning of the wheels and the lower vehicle side parties by horizontal wash cylinders on the left and right sides. Both horizontal wash cylinders pivot in the driving direction, mounted in a  tand construction and adjust to the exact width of each vehicle.

The wheel wash principal remains the same: The wheel area is washed by the wheel turning while passing the wash cylinder (left wheels turn on double chain conveyor along the cylinder).

Optionally available: Wash material BRUSH PREMIUM
Special polyethylene brushes (black/grey) with profiled trimming and mixed brush hair model (brush hair geometry, diameter and length) for increased cleaning performance.
 

Wheel wash device, wheel accompanying

Both wheel wash brushes are synchronously and pneumatically guided on the wheel pair to be washed. Correct control of the applied brush pressure as well as correct inner irrigation of the brush  guarantees a thorough rim wash. The wheel washer is activated via a light barrier system. Starting at this point it runs frequency controlled 1.000 mm with the wheels.
 

Wheel wash device

Stable linear guidance of the inner, irrigated wheel wash brushes. High cleaning performance through pulsating brush grip and rotation direction change. Wheel recognization via light barrier.
 

 

Under-chassis wash systems

Medium-pressure spray device for front, under-body and rear, floor installation above-ground

Designed for touchless cleaning of the lower front and rear surfaces with medium-pressure. The water jets overlap underneath the vehicle in the wash program “under-chassis wash”. This  aggregate is capable of being retrofitted in wash tunnels with existing foundations, due to its above-ground installation. With the respective supply device, the device can be operated with a working pressure of approx. 15 bar at approx. 100 ltr./min..
 

Wash tunnels concept
EVOLUTION - General technical specifications

 

Version

Premium

Operational concept

Short wash tunnel (serviced wash tunnel)

High-Level (serviced wash tunnel)

High-Level (Express)

Pit length

18.450 mm (minimum)

26.575 mm (minimum)

46.075 mm (minimum)

Design

steady

Individual colouring

Capacity

¹ up to 50 cars / h

² up to 80 cars / h

³ up to 110 cars / h

Chemicals

PROTECT SHINE

ALPINE WAX

FOAM REX

TWIN FOAM

RIM REX

and much more.

Service station supply and other

Washing accessories are very important for a good car wash. Those who rely on high-quality washing utensils can expect an optimal and scratch-proof car wash. In our shop you will find all necessary accessories from the washing bucket to the dry cloth.


Visit our christ carwash shop now »

 

Financing

We have the right financing model for you! It is important to have a tailored financing model that meets your specific needs. MMV Leasing is our long-standing partner in the area of this financial service. As market leader, our cooperation partner has more than 20 years of experience in this sector.

 

 

Leasing with FA


FULL AMORTIZATION

The total acquisition costs for the leased asset are fully amortized over the term of the lease agreement..

 


Leasing with PA


PARTIALLY AMAORTIZED

The total acquisition costs for the leased asset are only partially amortized over the term of the lease agreement.

 

 

Hire purchase


SALES BY INSTALLMENTS

This type of contract involves the sale of a leased asset in installments by the lessor to the lessee. Ownership of the hire-purchase item shall not automatically pass to the hirer until payment has been made in full.

 

Our team of experts is looking forward to your inquiries

 

 


Maricic, Marko

International Sales Manager

"The secret of success is to understand each other´s point of view"
Quote from Henry Ford, founder of automobile manufacturer Ford Motor Company

Contact request

*This field is required
*This field is required
*This field is required
Please select your country
*This field is required
*This field is required
A valid email address is required
*This field is required